unisonic technologies co., ltd 319 preliminary linear integrated circuit www.unisonic.com.tw 1 of 7 copyright ? 2011 unisonic technologies co., ltd qw-r101-031.b single phase dc motor drive ic ? description the utc 319 is particularly designed for a single phase dc motor driver circuit. it includes hall sens or and output coil drivers. the range of the operating voltage and the operation current is typically 0.3a. the utc 319 is a well performance integrated ic with less required external components. the high sensitivity of hall effect sensor is suitable for motors from mini-type cpu coolers to blowers and dc fans. ? features * operating voltage ranges wi dely from 3.0v to 20v * 1 chip hall sensor/drivers * output thermal shutdown protect circuit * output sink current up to 300ma ? ordering information ordering number lead free halogen free package packing 319L-G04-K 319g-g04-k sip-4 bulk ? pin description pin no. pin name description 1 v cc ic power supply 2 no coil driver output is low st ate during the n magnetic field. 3 so coil driver output is low st ate during the s magnetic field. 4 gnd ic ground
319 preliminary linear integrated circuit unisonic technologies co., ltd 2 of 7 www.unisonic.com.tw qw-r101-031.b ? block diagram 2 3 4 1 pre-driver thermal shutdown latch circuit temperature compensated current amplifier hall element voltage regulator hysteresis control sensitivity control
319 preliminary linear integrated circuit unisonic technologies co., ltd 3 of 7 www.unisonic.com.tw qw-r101-031.b ? absolute maximum rating parameter symbol ratings unit v cc pin voltage 20 v peak current 800 ma hold current 600 ma output peak sink current continuous current i out 300 ma t a =25c 600 mw power dissipation t a =70c p d 450 mw junction temperature t j +150 c operating junction temperature t j 0 ~ +85 c storage temperature t stg -65 ~ +150 c note: absolute maximum ratings are those values beyond which the device could be permanently damaged. absolute maximum ratings are stress ratings only and functional device oper ation is not implied. ? dc electrical characteristics parameter symbol test conditions min typ max unit supply voltage v cc 3 20 v quiescent supply current i vv v cc =20v, no use pin open 18 25 ma v ce(sink) v cc =14v, i c =200ma 0.55 0.8 v output saturation voltage v ce(drive) v cc =14v, i c =200ma 12.5 14 v ? ac electrical characteristics parameter symbol test conditions min typ max unit rise time t r r l =820 ? , c l =20pf 0.5 1.0 s fall time t f r l =820 ? , c l =20pf 0.5 1.5 s switch time differential t r l =820 ? , c l =20pf 1.0 0.5 s ? magnetic characteritics a grade parameter symbol min typ max unit operating point b op 10 45 release point b rp -45 -10 gauss b grade parameter symbol min typ max unit operating point b op 65 release point b rp -65 gauss c grade parameter symbol min typ max unit operating point b op 90 release point b rp -90 gauss
319 preliminary linear integrated circuit unisonic technologies co., ltd 4 of 7 www.unisonic.com.tw qw-r101-031.b ? typical application circuit utc 319
319 preliminary linear integrated circuit unisonic technologies co., ltd 5 of 7 www.unisonic.com.tw qw-r101-031.b ? application circuit the example of typical application circuit a typical application circuit is shown as follows. the r ed, yellow, and black wires are the input points of the motor system: red--the input of power supply; ye llow--the output of fg; black--the ground signal. r c is an external pull-up resistance for the use of measuring fg signal. the value of r c can be calculated by the transistor saturation voltage (v on ), sink current (i c ), and off-level voltage (v c ). c on c c i v v r ? = for example: v c =+5v for ttl level; i c = 10ma at 0.2v saturation voltage; the safety value of r c =470 there is a reverse protection diode d1 in the circuit. as if the red and black wires reversely connect with the power source, the current flows through the ground via ic and coils l1 and l2 to power supply. under such kind of circumstances the ic and coils are easy to be burned out. from that, this reverse protection diode is necessary in the design. meanwhile, an extra volta ge drop on the supply voltage should be taken into consideration, which is caused by the reverse protection diode. the capacitor c1 is designed to reduce the ripple nois e during the transient of t he output stages, and its value is determined by the coil impedance and characteristics. r wire b wire +v c r c y wire v cc c1 no so 319 gnd d1 l1
319 preliminary linear integrated circuit unisonic technologies co., ltd 6 of 7 www.unisonic.com.tw qw-r101-031.b ? functional information h-bridge transistor output in the following figure, the diagram of h-bridge transistors is shown. the single-phase motor rotation is changed by a switching current of coil l1. when the magnetic pole is n pole, q2, q3, q5 is shut of f and q1, q4, q6 is turn-on, the current flows through l1 from so to no. and when the magnetic pole is s po le, q1, q4, q6 is turn-off and q2, q3 is turned on. the current flows through l1 from no to so.
319 preliminary linear integrated circuit unisonic technologies co., ltd 7 of 7 www.unisonic.com.tw qw-r101-031.b utc assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all utc products described or contained herein. utc products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
|
